Saturday, October 29, 2011

Icom IC-2200H Adjustment Mode Jig




In order to adjust the power output of the IC-2200H transceiver it must come to "Adjustment Mode" and we need also the adjustment jig. The jig itself is made of 22K resistor connected to Pin7 and Pin2 of the RJ45 connector. When the jig is inserted to the microphone jack, "Adjustment Mode" can be initialized by holding the keys "SET" and "MONI" simultaneously while pressing "POWER ON"
The transceiver screen should look like this;


Adjustment items are displayed in the lower right corner of the LCD and these can be toggled by pressing the "BLANK OPT" or the "V/MHZ" keys. When the transceiver is on "Adjustment Mode" you can now remove the jig and reconnect the microphone. Please refer to the IC-2200H service manual for more details on the adjustment parameters. Note that the power output of the IC-2200H can be adjusted to 85W max by setting the PO parameter in the "Adjustment Mode". When done please perform a "Master Reset" to take effect the changes made on the transceiver.   ---73 de du1vss
Attachment: 2200H.pdf
Posted by at

17 comments:

  1. STEVE ALLANMay 22, 2012 at 2:55 PM

    Wired up jig plug with 22k resistor as above & followed all your instructions but could not get radio to go into Adjustment Mode.

    ReplyDelete
  2. ricardo III gerolaJune 5, 2012 at 9:17 AM

    tnx for the info sir DU1VSS FR. DW2ZIR

    ReplyDelete
  3. roy tanJuly 8, 2012 at 11:04 PM

    the problem on this modification, we can not identify on level adjustment using the knob because numbers and ABCDF letters appearing only, how can I determine on the exact level are we want to enter in order copy up the data base on IC2200H service manual particularly on page 5-2.

    ReplyDelete
  4. ricardo III gerolaJuly 9, 2012 at 3:02 AM

    download the service manual of 2200h and you can fine it what you want to adjust, tnx

    ReplyDelete
  5. jay balangueJuly 31, 2012 at 9:10 PM

    dodong guapo hehe

    ReplyDelete
  6. UnknownAugust 19, 2015 at 4:18 AM

    ...sir, pwede ba rin ito sa IC-2100 or IC-2300???

    ReplyDelete
  7. hevirredAugust 26, 2015 at 5:41 AM

    sa icom ic-2300H pwede ang jig. di pwede sa ic-2100H kasi walang service mode ang ganyang radio.

    ReplyDelete
    Replies
    1. UnknownApril 19, 2021 at 11:18 AM

      Sir bat ako noong pinasok ko ang jig tapis lumalabas sa lcd ay code.

      Delete
    2. DodongOctober 1, 2021 at 7:24 AM

      Hi sir 2200h po bakit code ang lumalabas

      Delete
  8. AnonymousSeptember 9, 2017 at 6:39 AM

    Hi po nakapasok na ako sa adjustment mode pagkatapos?

    ReplyDelete
    Replies
    1. hevirredSeptember 10, 2017 at 5:45 PM

      Wag ka muna gumalawng mga setting dyan sir kasi mahirap na yan ibalik, basahin mo muna ang service manual ng ic-2200h.. nasa ilalim ng post ko ang service manual, paki download na lang.

      Delete
  9. AnonymousOctober 1, 2017 at 2:35 AM

    Hi do you have a copy sa default value sa adjustment mode just in case ibalik ko sa dati. Tnx

    ReplyDelete
  10. hevirredOctober 2, 2017 at 5:41 PM

    nagalaw mo ba? tsk tsk tsk.. pwede kong i check ang setting ng aking ic-2200h pero di ako sure kung mag wowork sa unit mo..

    ReplyDelete
  11. UnknownNovember 15, 2020 at 5:27 AM

    dapat nkalagay ang mga exact adjustment pra un nlng hanapin dami kc ang pinipilian dko alam alin don boss pls.specify.salama

    ReplyDelete
  12. UnknownFebruary 27, 2021 at 8:14 AM

    Sir, pwede ba yan sa ic2300h? And paano mo makakuha nung jig na nilalagay?

    ReplyDelete
  13. UnknownMarch 2, 2021 at 5:42 AM

    Dapat may service monitor kayo kung gagalawin nyo yan, dapat monitor nyo lahat ng parameters.

    ReplyDelete
  14. PT9TLMay 24, 2021 at 7:56 AM

    And IC-V8000 ?

    ReplyDelete

Subscribe to: Post Comments (Atom)